Tag Archives: diy furniture

Webbing a Wooden Couch Frame

If you have any furniture with a wood frame and loose cushions, it’s a good bet you you have a piece of furniture supported by webbing. And if your furniture is old and the webbing is original, it’s another good bet it’s not supporting your butt–or anyone else’s for that matter–the way it used to.

This is a problem we’ve been experiencing for a few months with the ’60s platform couch in our living room. The couch felt less than totally stable, and I was constantly noticing that the cushion slid forward when anyone sat on it. When we bought it, I didn’t really know to check under the cushions, but when I finally gave the seat some attention, I discovered the culprit was some mega stretched-out and partially deteriorated webbing.

Loose webbing on a vintage wooden couch frame

Sure, this looks like it might make a comfy hammock, but in general you don’t want your butt to continue sinking toward the ground after you’ve already had a seat. It was past time for new webbing.

Luckily, webbing the seat of a couch is a pretty simple and relatively inexpensive project you can easily do yourself with only a couple tools and supplies. It didn’t make much mess, and the only things needed were a roll of jute webbing, two pair of pliers, a pneumatic staple gun, a some 5/8″ staples.

First, Justin removed the old webbing.

Then, it was just a matter of attaching the new webbing in a simple weave pattern. We made sure to cut the webbing a few inches longer than the seat on both ends. When securing it, we stapled each end, then folded the excess over and stapled again for added stability.

Stapling jute webbing

We finished the short side first.
New webbing on a wooden couch frame

Using the same stapling technique, I weaved the longer pieces through the shorter pieces.

The only real trick to this is keeping the webbing taut. There is a contraption called a webbing stretcher that exists for this expressed purpose, and if you are one person doing this job, you will probably need one. Because Justin helped with this, he was able to pull while I stapled. What worked best was for him to grab the webbing using two sets of pliers rather than his two hands. He also sat on the floor and pushed the against the couch with his feet for even more superior resistance (I’ll leave you to ponder that image in your free time).

That’s all folks! Done.
Weaving new webbing on a wooden couch frame

And done.

The webbing cost around $35 for 75 yards, and we used about 15 yards for this project, so all in all, it cost about $8 and took an hour of our weekend. Still, this small change made a world of difference in the comfort of our couch and probably the longevity of frame and cushions alike. As an added bonus, my husband got to play Justin Plierhands for a short while, and an evening at my place no longer means guests will enjoy saggy bottom with their sparkling conversation. Everybody wins.

Upholstered! 1964 Paoli Chair

There was snow on the ground when we found these three 1964 Paoli chairs at an estate sale last winter.
1964 Paoli chairs before reupholstery, found at an estate sale
Since then, they’ve spent a lot of time chilling out in the basement, waiting to get a little TLC. But for everything there is a season, and apparently summer is the season for Paoli chairs, because they are finally done!
 Reupholstered white mid century Paoli chairReupholstered blue or gray mid century Paoli chair
You can follow the upholstery process for chair three below.


The process of stripping these Paoli chairs was far less dramatic and eventful than the loveseat, which was dangerous and, frankly, a little disgusting. I started with the chair upside down to get easier access to the staples.
IMG_2713 IMG_2714
The good news is that all the staples were on the narrow underside of the seat back. Once those were removed, I detached the fabric and moved on to the seat.
IMG_2726 IMG_2727
I must have seemed like I needed some assistance, because Jellybeans came out to supervise my efforts.
White dog helping me upholster
Boom! With the staples gone from the seat, the stripping process is done. QC came back to check the cushion density one last time, just to make sure it was good for sitting and all.
IMG_3229 IMG_3231

Sewing the Seat Cushion Cover

You’ll have to excuse me if some of this seems like one of those cooking shows where the host suddenly pulls the finished dish out of the oven. Since this was the third of these chairs I did and the second in the same fabric, I had already cut my material to size. However, I do promise to cover measuring for yardage, pattern making, and cutting fabric in future posts.

The seat cushion cover consists of two parts: the seat and the boxing. The original chair also had piping, but I opted to go sans piping for this time because I wanted a clean, modern look and  thought a simple cover accomplished that better. I did use piping on the first chair, and that looked great, too.

With the seat and boxing fabric already cut, the first step was to trace the outline of the seat cushion onto the seat fabric. On the first chair, I did a truly embarrassing amount of seam ripping before finally accepting that this cushion is an irregular shape, and eyeballing it while you sew is not an especially effective way of getting that shape right.

This time I broke out the chalk pencil to make sure my seam placement was exact. It’s okay to draw on the correct side of the fabric–the side that will be showing on the final product. A lot of the chalk line will not show after you have sewn, and what does show can be patted out with a damp cloth. I made the curve of the cushion my boundary, marking for my seam where the cushion began to slope downward. This cushion had a little bit of edge there, which made the process pretty easy.
Measuring fabric for a seat cushion
Next, I brought out the boxing (two pieces, already sewn together). I wanted to place the side seams of the boxing near where the back leg of the chair meets the seat so that they would be less visible. This is also the way the previous seat was assembled, so it’s not as if I had to think of that genius strategy on my own.

I laid out the boxing so that the seams met the seat and the same place on both sides. Then, I made a horizontal marking on the seat fabric to indicate where the boxing seam should go.
Fitting boxing for a seat cushion Marking a seat cushion to be sewed
Before sewing, I pinned the boxing to the seat fabric.
Pinning boxing to a seat cushion before sewing
When pining, I made sure to do the following three things:

  1. Arrange the top side of the seat fabric and the boxing so they are facing each other (ie–the seat fabric is facing up, and the boxing is facing down), and the boxing is inside the seat cushion. That way, when I folded the boxing back over, it was underneath the seat and ready to cover the bottom of the cushion.
  2. Begin by pinning the BOTH boxing seams on the horizontal markings I just made. If you start with just one, there is no guarantee you will distribute the fabric exactly as needed for the other one to line up.
  3. Pin on top of the yellow line drawn on the seat fabric. It wasn’t visible once I added the boxing, so the pins became my guide when sewing, like so:

Sewing boxing for a seat cushion

Upholstering the Seat Cushion

Then I covered the whole seat with a half layer of dacron and stapled it to the bottom, just to even out the cushion and freshen the padding a little bit. I also noticed on the other chairs that there could be a slight bulge where the seat cushion met the plywood bottom, so I put an extra strip of dacron across the front to smooth out that area. At this point, my cushion looked like this:
Covering a cushion in dacron
Now I was ready to add the seat cushion cover. It fit pretty tightly, which I just what I wanted. I smoothed as I went, making sure the seams were where I wanted them, and the grain of the fabric was straight.

After flipping the cushion over, I pulled the boxing down and secured it to the bottom. The top and bottom of a piece should always be stapled before you move to the sides. I checked the front periodically to make sure I was pulling evenly and not getting my seam out of alignment. When completely stapled, the bottom looked like this:
To complete the seat, I added a piece of cambric, which is a fancy word for the black dust cover that’s always hanging off the bottom of old sofas. Strictly speaking, this is optional, since cambric doesn’t really do anything functional. It does, however, make the whole job look more finished and keeps strings from the raw edge of your fabric and bits of dacron from being visible. Attaching cambric is about the easiest part of the entire project. Just cut it to shape and staple around the outside. It’s nice to fold the edge of the cambric under before stapling, but it won’t unravel, so if there isn’t enough fabric to fold, no one will be the wiser.
Applying cambric or a dust cover to the bottom of furniture

Upholstering the Seat Back

I try to reuse the original materials from furniture whenever possible. It’s greener and easier on the wallet. The cotton batting from this chair was in fine condition, so back on it went. To add extra padding and a smooth finished surface, I added a layer of dacron over the batting and stapled it to the back.
IMG_3253 IMG_3258
First, I upholstered the front side of the seat back by draping the fabric over the front and securing it on the back top and underneath the bottom of the seat. As with the seat cushion, I smoothed and stapled the top and bottom of the fabric before doing anything with the side, like this:
When I had stapled the back top and bottom all the way across, I needed to make a release cut. This small split in the fabric where the arm meets the back enabled fabric to be wrapped around the arm
After making release cuts on both sides, I finished stapling the top and bottom of the back. When I came to the arms, I folded the extra fabric from the cut underneath before stapling. The front and back then looked like this:
IMG_3264 IMG_3265
Now I was ready to move to the seat back and was kind of almost done. I positioned the top of the fabric at the top of the seat back and draped the rest backwards over the seat front. I stapled across the top to secure, then added a piece of cardboard tack strip and stapled again in the same manner. This ensures a straight, clean edge on the back of the chair.
IMG_3266 IMG_3267
I added a half sheet of dacron to cover over where the tack strip was applied and smooth out the whole surface. Then, I flipped the back fabric down and stapled it to the underside of the seat back. I folded the fabric under as I stapled so that no raw edges were exposed. With the bottom completed, only the sides were still loose.
IMG_3269 IMG_3271
The sides of this back were finished with a nail head trim. To apply nail head, all I needed was nail head (of course) and a mallet to whack the tacks with. Some of the original tacks bent when I removed them, so I had to get new ones to finish this chair. At $1.50 for 24, they were a minor expense.
And voila!
Nail head trim on the back of a chair
To be honest, I forgot to take a picture when I first attached the nail head, which is why the above pic is not a sketchy basement pic like the rest AND already has cording where the seat back meets the arm. Oops! That’s a teaser for you as we head into the LAST STEP(s).

Sewing Double Welt Cording

Double welt cording is good for finishing areas of furniture where wood meets upholstery. When sewn, the raw edge of the fabric hides on the bottom of the cording, and it can be attached with staples. Back at the sewing machine, I cut a small piece of fabric and two short pieces of 5/32″ cording.

5/32" cording IMG_3282
You can get a cording foot or a double cording foot for your sewing machine, but I don’t have either yet, so I used the zipper foot that came with my machine. I attached it on the left side and moved the needle to the left position so it could get as close as possible to the cording.
I folded fabric over the first piece of cording and sewed, then arranged the second piece right next to it and folded over again.This time, the seam needed to be placed in between the two pieces of cording. This is where the zipper foot isn’t totally adequate to the project. The cording is too thick for the presser foot to be lowered, but if the presser foot is left up, the threads on the back side can get pretty messy. When only dealing with small pieces like this, I prefer to hand sew. On the finished cording, notice I made the fabric about a 1/2″ longer than the cording. This makes it much easier to staple.
IMG_3286 IMG_3290
I positioned the cording on the joint of the arm, stapled, and that’s a wrap (no pun intended). The last chair could finally be joined up with its twin.

Gray mid century Paoli chairs, reupholstered
As much as I enjoyed working on these chairs, I am excited to get them the heck out of my basement. They need to move on to forever homes where they can be displayed and loved, as the furniture gods intended.

Stripped! Mid-Century Loveseat

As a teenager, I hate hate hated science and especially dreaded dissection day in biology class. But when it comes to furniture, I kind of enjoy ripping stuff open and digging around in its guts.

Even so, this mid-century loveseat was hiding a few surprises I definitely was not expecting.

Purple mid-century loveseat rescued from a yard sale

We found the loveseat at a garage sale. We’d been looking for a small couch for our TV room, but most loveseats we found were either too large and overstuffed or outside our price range. I loved this one for its classic lines and small size. But, the host of the garage sale wasn’t sure she could let it go, so we left our phone number and asked her to give us a call if she changed her mind. And bingo–we got the call that very evening to pick up the loveseat AND a matching pair of mid-century chairs. Victory!

The woman who sold us the couch told us it had been living in her garage, but sometimes the thrill of the find temporarily suspends my powers of reasoning, so it didn’t really penetrate what conditions it had been subject to or what might have had access to it.

Soon after we got the couch home, Justin tore the dust cover off the bottom to find this:

Snake skin found inside loveseat


And that was just the beginning. Also in the process of stripping this couch, I found a more than generous amount of mouse poop, and no fewer than 7 LIVE brown recluses + a few additional dead ones. For a while I was pretty sure I had also found some snake eggs, but they turned out to be acorns (hence the poop):

Mouse poop and eaten acorn found in furniture batting

Let’s just say I was extremely relieved when the couch was down to the frame and I could finally be fairly sure nothing else poisonous was going to crawl out of it.

Now, on to the actual stripping! Have you ever stopped to consider what’s keeping the cover on your couch? Before I started working on furniture, I really never had. But now I can tell you–it’s staples. Lots of them. For this particular couch, about this many of them:

Staples removed from a loveseat during reupholstery

AND you have to remove them all pretty much by hand, so stripping upholstered furniture is a labor intensive process that can be quite time consuming.

Here are the tools and supplies I used:

Tools for stripping furniture: pliers, staple remover, gloves, dust mask

1. Staple remover – This grabs and pries out the staples. If you don’t have a staple remover, you can use a small flat head screwdriver, but be very careful. Prying out stuck staples sometimes takes a lot of force, and if your tool loses purchase on the staple, the screwdriver can come back flying toward your eyeball. I speak from experience here and feel very lucky to be typing this still with two good eyes.

2. Pliers – Removes staples after you have pried them up with the staple remover.

3. Leather gloves – Protects your hands from scrapes and cuts. These are really important. Especially if you’re working on older furniture, staples can break in half, leaving them hidden in fabric or padding. On one of my first projects, I was pretty sure I was going to have to get a tetanus shot after I got a splinter from a shard of rusty staple (figured out later that my last shot was still good–whew!).

4. Dust mask or particulate respirator – Keeps your lungs feeling good. Ripping furniture and digging out padding releases tons of dust, fibers, and other unknown stuff that you don’t really want to inhale. I hadn’t thought about this too much until I talked to a retiring upholsterer who said he had developed respiratory problems from years of exposure to dust and the chemicals in fabrics. Now I play it safe.

5. Goggles – Like a dust mask for your eyes! All that floating stuff you block out of your nose and mouth can still make it up to your eyeballs, and it can be ridiculously painful. Again, play it safe.

When you start removing fabric, you want to work in the reverse order from how it was attached. That’s why you’ll notice I begin with the back of the couch and work my way forward.

Day 1:

Stripped couch or sofa

Day 2:

Stripped couch or sofa

Day 3:

Couch or sofa stripped to the springs

Couch or sofa stripped to the springs

Couch or sofa stripped to the springs

Now comes the fun part! This little lady is free of creepy-crawlies and ready for some new threads.